remise à zero le compteur d'imprimante CANON+EPSON
ط¢ط®ط±
ط§ظ„طµظپط­ط©
khalilo6
  • ط§ظ„ظ…ط´ط§ط±ظƒط§طھ: 52
    ظ†ظ‚ط§ط· ط§ظ„طھظ…ظٹط²: 5
ط¹ط¶ظˆ ظ…ط¨طھط¯ط¦
khalilo6
ط¹ط¶ظˆ ظ…ط¨طھط¯ط¦
ط§ظ„ظ…ط´ط§ط±ظƒط§طھ: 52
ظ†ظ‚ط§ط· ط§ظ„طھظ…ظٹط²: 5
ظ…ط¹ط¯ظ„ ط§ظ„ظ…ط´ط§ط±ظƒط§طھ ظٹظˆظ…ظٹط§: 0
ط§ظ„ط£ظٹط§ظ… ظ…ظ†ط° ط§ظ„ط¥ظ†ط¶ظ…ط§ظ…: 6850
  • 17:23 - 2007/06/12

 

 

 

 

remise à zero le compteur d'imprimante CANON+EPSON

procédure.
 
     MINI LEXIQUE:
 
Power button = bouton d'alimentation
Resume button = bouton Reprendre/Annuler
Power Off = éteindre
Power On = allumer
Hold ou Hold on = maintenir appuyé, en gardant le doigt dessus
Press = appuyer juste une impulsion
Release = relacher
Once= une fois
Twice = 2 fois
Both = les 2
Steady = allumé de façon permanete pour un voyant
Flash = clignote pour un voyant
 
 
Canon GENERIC "S" SERIES RESET CODE
Waste Ink Counter Reset.
(1) Turn off the printer.  
(2) Press and hold the RESUME button, then press and hold the POWER button.  
(3) Release the RESUME button, Next press and release the RESUME button two(2) more times in
      succession. Note: you are still holding the POWER button). The printer's carriage will "reset"  
      or move momentarily. If the above was properly performed the printer will enter the  
     "Service Mode".  
(4) Press the RESUME button 4 times, this will select the clear waste ink counter function. The lamp  
      will alternate (change) color with each key press.  
     1. Service/Factory test printout, including ink sensor check.  
     2. EEPROM - Info printout.  
     3. EEPROM - Initialization.
     4. Reset the Waste ink counter.
     5. Printer model setting. (More selections beyond this point - However it is best leave them unaltered - You have been warned!)  
After selecting the desired mode (eg 4), press the POWER button to "set" the change, and return to the top of the function selection menu. Press the POWER button again to restart the printer.  
********************************************************************************************************************************Canon i250 (Merci à Gubew et à Manuec)                             
1 eteindre l'imprimante et débrancher le cable d'alimentation
2 tenir enfoncé le bouton d'allumage (jusqu'a la fin) et rebrancher le cable d'alimentation
3 la diode doit être verte
4 appuyer et relacher le bouton éjection feuille (resume) la diode doit être orange
5 appuyer  le bouton éjection feuille (resume) la diode doit être verte
6 relacher les 2 boutons
mon ordinateur a détécté un nouveau matériel et tout est rentré dans l'ordre.
 
******************************************************************************************************************************** 
Canon i320, i255                                                          
Waste Ink Counter Reset.
Step 1 : Manual Temporary Only
1. Unplug power and USB.
2. Open door and hold power button.
3. Connect power.  
4. Close door, then release power button.
 
For Reset by software
or Step 1: Manual for service mode
1. Turn off the printer. And disconnect the printer cable.
2. Press and hold the POWER button, turn on the printer.  
3. The indicator (L.E.D.) should be green.  
4. Press and release the RESUME button , the indicator (L.E.D.) should be orange.  
5. Press and release the RESUME button again, the indicator (L.E.D.) should be green.  
6. Release both buttons.  
 
step 2 : Software for Permanant  
 
1. Reconnect the printer cable.
2.Open General Tools software and select (USB PORT)
3 .Choose (SET DESTINATION 1) And it should be reset.
 
Remark "After service mode Pls use software for permanent reset"
 
*********************************************************************************************************************************
Canon i450                                                   
1- Close the access cover, and turn off the printer.  
 While pressing the Resume button, press and hold the Power button  
 (The led lights in green to indicate that the function is selectable)  
2- While holding the Power button, release the Resume button  
3 -While holding the Power button, press the Resume button 2 times,  
 and then release the Power and the Resume buttons.  
 (In the operation panel, "02" will be displayed.  
 Each time the Resume button is pressed, the Led lights alternately in  
 either orange or green. During initialisation, the Led blink in green).  
4- When the Led stops blinking and lights in green,  
 press the Resume button 4 times.  
 (Each time the Resume button is pressed the Led lights alternately in  
 either orange or green, and now the Led is green).  
5- Press the Power button. the Led lights in green, and the function is performed.  
 (When the operation completes, the printer returns to step 4 above)
 
******************************************************************************************************************************** 
Canon PIXMA IP1000, IP 1500                                                      
Waste Ink Counter Reset.
Step 1: Manual for Service mode
1. Turn off the printer. And disconnect the printer cable.
2. Press and hold the POWER button, turn on the printer.  
3. The indicator (L.E.D.) should be green.  
4. Press and release the RESUME button , the indicator (L.E.D.) should be orange.  
5. Press and release the RESUME button again, the indicator (L.E.D.) should be green.  
6. Release both buttons.  
 
step 2 : Software for Permanant  
 
1. Reconnect the printer cable.
2.Open General Tools software and select (USB PORT)
3 .Choose (SET DESTINATION 1) And it should be reset.
 
Remark "After service mode Pls use software for permanent reset"
 
******************************************************************************************************************************** 
Canon i850, i950, S600                                                       
Start with the printer OFF  
1. Hold down RESUME and then hold down POWER  
2. release RESUME  
3. press RESUME twice, then release POWER  
4. Let green light blink until printer is done futzing  
     Select function with RESUME press POWER to execute:  
     presses - light color - function
Number of presses  - light color - function  
0 presses - green - Test print (or exit service mode on i960)  
1 press - orange - EEPROM info print (plus grid nozzle diagnostic on i960)  
2 presses - green - EEPROM initialize  
3 presses - orange - Reset waste ink counter
 
******************************************************************************************************************************** 
i965 Canon                                                 
1/  ETEINDRE  
2/  APPUYER SUR EJECTION ET MAINTENIR  
3/  APPUYER ET MAINTENIR MISE EN ROUTE (POWER)  
4/  APPUYER  1 FOIS SUR EJECTION (RESUME) LE LED DEVIENT ORANGE  
     APPUYER 1 DEUXIEME FOIS ET IL DEVIENT VERT  
5/                      VOUS ETES (peut être) EN MODE SERVICE  
6/ RELACHER MISE EN ROUTE CA PASSE AU VERT  ET LE CHARIOT BOUGE  
                  ATTENDEZ QUE CA SE CALME ET QUE CA REPASSE AU VERT fixe  
7/ APPUYEZ 4 FOIS SUR EJECTION  POUR REMETTRE LE COMPTEUR A ZERO .  
   Le led passe alternativement du vert à l'orange  
8/ APPUYER SUR MISE EN ROUTE (peut être plusieurs fois) POUR ETEINDRE  
   Ensuite vous allez tester si le miracle s'est produit  
 
******************************************************************************************************************************** 
Canon S450 Printer                                                              
1: Power off printer
2: Hold Resume button then press and hold POWER, the beeper will sound once.  
3: Hold POWER and release RESUME  
4: Press RESUME twice  
5. Release Power button
6: When the indicator lights steady, press RESUME three(3) times. The indicator should be orange.  
7: Press Power to set data
 
******************************************************************************************************************************** 
Canon BJC 1000 Serie                                                               
1: Remove Cartridge
2: Unplug the AC Power Cord
3: Hold down the RESUME button
4: Release RESUME after plugging in the AC Power cord.  
5: Press the RESUME once within 5 seconds and release the RESUME .  
6: Press and HOLD RESUME for two seconds or more and release it.  
7: Press and HOLD RESUME for two seconds or more and release it.  
8: Unplug AC Power Cord to set data.
 
********************************************************************************************************************************
 
Canon BJC-2000 BJC-2100 Serie                                                        
1: Remove the Cartridge  
2: Unplug the AC Power Cord  
3: Close Front access panel  
3: Hold down the RESUME/RESET button and plug in the AC power cord  
4: Release RESUME/RESET after plugging in the AC Power cord.  
5: Press the RESUME/RESET once within 5 seconds and release the RESUME/RESET .  
6: Press and HOLD RESUME/RESET for two seconds or more and release it.  
7: Press and HOLD RESUME/RESET for two seconds or more and release it.  
8: Unplug AC Power Cord to set data.
*********************************************************************************************************************************
 
Canon BJC-210 BJC-240 BJC-250 BJC-255 BJC-265                                              
BJC-4200 BJC-4300 BJC-4400 BJC-4550 BJC-4650Canon BJC-4100                                  

Unplug Power Cord
Hold POWER and RESUME buttons  
Plug in Power Cord  
Release buttons  
Open front door of printer  
Hold the CARTRIDGE and RESUME buttons  
Press POWER  
Release all buttons after the beeps  
Press CARTRIDGE once  
Press RESUME
Canon BJC-5000
1: Power off printer  
2: Press and hold RESUME then press POWER, The indicator will start blinking.  
3: While the indicator is blinking , Press RESUME twice then Wait until the printer beeps to indicate service mode
5: When the indicator lights steady GREEN, press RESUME four(4)times. The indicator should be      GREEN.  
6: Press Power to set data
Service Test Print  
1: Power off printer  
2: Press and hold RESUME then press POWER, The indicator will start blinking.  
3: While the indicator is blinking , Press RESUME twice then Wait until the printer beeps to indicate      service mode
5: When the indicator lights steady GREEN, press RESUME two(2)times. The indicator should be      GREEN.  
6: Press Power to Print  
Nozzle Print
1: Power off printer  
2: Press and POWER, until the printer beeps and release.  
Demonstration Print
1: While the printer in ON , , Press and hold RESUME until the printer plays a melody of beeps.


 ******************************************************************************************************************************** 
Canon BJC-5100                                                                          
Self Test
Switch Printer off. Hold Power for 1 beep.
 
Waste Counter Reset  
1: Power off printer  
2: Press and hold RESUME then press POWER, The indicator will start blinking.  
3: While the indicator is blinking , Press RESUME twice then Wait until the printer beeps to indicate      service mode
5: When the indicator lights steady GREEN, press RESUME four(4)times. The indicator should be      GREEN.  
6: Press Power to set data
Service Test Print  
1: Power off printer  
2: Press and hold RESUME then press POWER, The indicator will start blinking.  
3: While the indicator is blinking , Press RESUME twice then Wait until the printer beeps to

indicate service mode
5: When the indicator lights steady GREEN, press RESUME two(2)times. The indicator should be GREEN.  
6: Press Power to Print  
Nozzle Print
1: Power off printer  
2: Press and POWER, until the printer beeps and release.  
Demonstration Print
1: While the printer in ON , , Press and hold RESUME until the printer plays a melody of beeps.
 
******************************************************************************************************************************** 
Canon BJC-3000 BJC-6000 BJC-6100 BJC-6200 S400 S450 F300 F600 F620                      
Canon BJC-7000 BJC-7100 BJC-8000 BJ-F800 i6500                                        
Waste Reset
1: Power off printer  
2: Hold Resume button then press and hold POWER, the beeper will sound once.  
3: Hold POWER and release RESUME  
4: Press RESUME twice then release BOTH POWER and RESUME buttons
5: When the indicator lights becomes steady, press RESUME three(3) times. The indicator should be ORANGE.  
6: Press Power to set data
 
Model Type reset
1: Power off printer  
2: Hold Resume button then press and hold POWER, the Green Indicator will light.  
3: Hold POWER and release RESUME  
4: Double click RESUME then release BOTH POWER and RESUME.
5: Press resume 4 times, Green Indicator should be lite.
6: Press POWER to enter the MODEL setting mode.
7: if the indicator is GREEN this is BJ-F620
to Set BJC-6200, press RESUME 1 time , the indicator should be ORANGE.
8: Press POWER to save
 

Canon BJC-600 BJC-600e BJC-610 BJC-620                                                       
1: Unplug Power Cord
2: Hold POWER and FF and Print Mode buttons  
3: Plug in Power Cord  
4: Release after the beeps
 
*********************************************************************************************************************************
Canon BJC-50 BJC-55 BJC-80 BJC-85 M40 M70                                                          
1: Unplug Power Cord
2: Hold POWER and RESUME buttons
3: Plug in Power Cord  
4: Release buttons after the printers starts up  
5: Hold CARTRIDGE and RESUME  
6: Press POWER  
7: Release all buttons after the beeps  
8: Press CARTRIDGE 16 times  
9: Press RESUME  
10: Unplug the Power cord
 
******************************************************************************************************************************** 
Canon BJ-30 BJC-35v BJC-70                                                                   
F14 Error Reset
1: Unplug adapter  
2: Hold POWER  
3: Plug in ADAPTER  
4: Release POWER after printer starts  
5: Hold FF and MENU and press POWER  
6: Release after beeps  
7: Press <> Cartridge until 1A is displayed  
8: Press ONLINE  
9: Press POWER to shutoff printer  
10: Unplug printer then re-plug printer  
 
******************************************************************************************************************************** 
Canon BJ F900, F890, F700, F500, S900, S820, S750 and S520                                                   
Turn off the printer.  
Press and hold the RESUME button, then press and hold the POWER button.  
Release the RESUME button, then press and release the RESUME button two more times in succession. (youre still holding the POWER button during this). The printer mechanics will move momentarily.  
You are now in Service mode.  
Pressing the RESUME key will select a function; for example, pressing RESUME 4 times will select the clear waste ink counter function. The lamp will alternate color with each key press.  
1. service/factory test printout, including ink sensor check  
2. EEPROM info printout  
3. EEPROM initialization  
4. Clear the waste-ink counter  
5. Printer model setting. (more selections beyond this- leave this alone)  
After selecting mode, press the POWER button to commit the change, and return to the top of the function selection menu. Pressing the POWER button again turns off the printer for a resta
 
******************************************************************************************************************************** 
Canon S9000, S300, S400, i550, i560, i850, i860, i865, i9100, i9950, PIXMA IP3000, IP2000   
1. Turn off printer
2. Hold down Resume button and press Power button.
3. Keep holding down Power button and let Resume button go.
4. Press Resume button 2 times then let BOTH buttons go.
5. Green lights will flash and then stop blinking.
6. When green lights are solid, press the Resume button 4 times.
7. Press the Power button and the printer should turn off, if not, press the Power button once more.
8. Your printer should respond as normal.
 
******************************************************************************************************************************** 
Canon S900, S820, S750, S520                                                   
Turn off the printer.  
Press and hold the RESUME button, then press and hold the POWER button.  
While still holding the POWER button, Release the RESUME button, then press and release the RESUME button two more times in succession.  
The printer mechanics will move momentarily. You are now in Service mode. Release the Power Button.  
Pressing the RESUME key will select a function; for example, pressing RESUME 4 times will select the clear waste ink counter function. The lamp will alternate color with each key press.
 
1. Service/factory test printout, including ink sensor check
2. EEPROM info printout
3. EEPROM initialization
4. Clear the waste-ink counter
5. Printer model setting. (more selections beyond this- leave this alone)
  
After selecting mode, press the POWER button to commit the change, and return to the top

of the function selection menu. Pressing the POWER button again turns off the printer for a restart.  
  
******************************************************************************************************************************** 
Canon S9000                                                            
Turn off printer  
Hold down Resume button and press Power button.  
Keep holding down Power button and let Resume button go.  
Press Resume button 2 times then let BOTH buttons go.  
Green lights will flash and then stop blinking.  
When green lights are solid, press the Resume button 4 times.  
Press the Power button and the printer should turn off, if not, press the Power button once more.  
Your printer should respond as normal.  
 
******************************************************************************************************************************** 
Canon MP110 Merci à Solal 74                                               
Step1
Suivez s'il vous plaît lmunissez vous de tournevis cruciformes
 
1. Après avoir enlevé la boite de cartouches d'encre, déconnecter l'imprimante de la mise en tension et de la connexion USB
2. renverser l'imprimante le bas en haut  
3. Au fond, vous pouvez voir il y a des vis cruciformes
4. Elles maintiennent l'alimentation
5. dévissez-les
6. Et déboiter soigneusement la boîte "noir-grise d'alimentation"
7. Alors vous verrez une le cordon d'alimentation avec l'imprimante terminé par une mini prise blanche.
8. Employer une pince adhoc pour le sortir avec grard soin.
9. Laisser l'alimentation au repos pendant 30 minutes, la carte eeprom va se décharger de son contenu
10. Reconnecter soigneusement le cordon par sa prise blanche (délicat si on a pas des petit doigts) le détrompeur de la prise évite d'inverser le sens d'introduction.
 
Step2
Allumez l'imprimante après connexion au réseau électrique
(1) pressez scan - copy - scan pour avoir accès au paramétrage
(2) ACCEDER AU MENU NVRAM
(3) METTRE ABS-M  à 0
(4)METTRE ABS-P à 0
(5) SORTIR DU MENU DE PARAMETRAGE
(6) reconnecter le cable USB et l'alimentation, remettre les cartouches
(7)puis quelques pages de test d'impression pour réamorcer les cartouches
 
******************************************************************************************************************************** 
Canon MPC 190 / MPC 200                                                             

Reset Waste Ink  
1) Enter SERVICE MODE.
     By pressing Menu, Copy, Scan, Copy, Copy  
2) Select TEST MODE.  
3) Select [8] PRINTER TEST in TEST MODE.  
4) Select 3. [EEPROM CLEAR].  
5) Select 0. [INK COUNT].  
6) Press the [Set] key.  
7) Press the [Stop/Reset] key (returning to the state of 3)), and then press the [ON/OFF] key
 
Canon MP 370
 
1) Printer on, press Additional Functions, Scan, Copy, Scan. Now you should be in service mode from there for waste ink tank reset it is simalar to what has already been posted  
 
2) Select Test mode which is like the last available selection  

3) Select #8 Printer Test, it will do something here like cleaning or something then it will come up with some other option this is where it gets a bit confusing cause now all it says is like 8-2 or 8-3 push the + or - button until it says 8-3 then hit the select button  
4) The menu will now say EEPRON Clear. Select Ink count which is option (0) and press set  
5) Select Ink count which is option (0) and press set.
 
******************************************************************************************************************************** 
Canon MP 400/MP 730/MP 600                                                           
 
1) Enter SERVICE MODE.---
By pressing Menu-Copy-#
 
2) Select TEST MODE.
3) Select [8] PRINTER TEST in TEST MODE.
4) Select 3. [EEPROM CLEAR].
5) Select 0. [INK COUNT].
6) Press the [OK] key.
7) Press the [Stop/Reset] key (returning to the state of 3)), and then press the [ON/OFF] key.
 
*********************************************************************************************************************************
Canon MPC 400 / MPC 600 Erreur ##343                                                     
 
1. Go to menu by pressing the > button
2. press [copy] and then #
3. go to 'test mode' by pressing > several times
4. press "OK"
5. now press 8 then 3 then 0
6. After that press the on/off button, everything should be fine now.
 
******************************************************************************************************************************** 
Canon MP730                                                            
 
1. Hit the "menu": Key
2. Hit "Copy" Key
3. Hit "#" Key
4. Scroll thru the menu headings until you come to "Test Mode" - 12th heading
4a. Hit "8" to select Printer Test
5. Hit the "3" button- this will bring up Eprom Clear
6. Hit "0" button
7. Hit the "Stop" button
After completion of step 7, turn printer off and On again to set the new settings
 
********************************************************************************************************************************  
Canon MP750 / MP780                                                            
  
1. Service menu: Menu -> Scan -> Copy -> Scan  
2. Select "TEST MODE"  
3. Select "[8] ETC.."  
4. Select "[4] EEPROM CLEAR"  
5. Select "[1] INK COUNT

"  
6) Press the [OK] key.  
7) Press the [Stop/Reset] key (returns you to the TEST MOD sub-menu))  
press the [ON/OFF] key (which resets the printer)  
 
  
Toutes ces infos proviennent des sites suivants:
http://www.neilslade.com/Papers/inkjetstuff11.html
http://www.cyber-ink.com/member-canon.html
 
 
3 - NETTOYAGE DES FEUTRES:
 
Avant de vous lancer dans cette manip lisez bien tout ce topic, et surtout consultez les liens où il est expliqué comment démonter une imprimante.
 
Une fois le compteur remis à zéro c'est comme si on roulait sur la réserve du réservoir d'essence d'une voiture, on peut encore rouler, mais pas 500Km.
 
Donc après avoir remis ce compteur à zéro, quand je dis après, il n'y a pas urgence, mais pensez à le faire, il vous faudra démonter votre imprimante.
 
Habillez-vous en dégueulasse, une giclée d'encre est vite arrivée  
 
Toutes les Canon sont faites de 3 parties, le dessus de la coque, la partie imprimante (rouleau, tête, électronique etc) et le fond partie basse de la coque.
 
Démonter la coque est assez délicat vu qu'elle est clipsée et non vissée, mais en faisant ça avec soin c'est possible.
 
Pour sortir la partie imprimante il y a des vis à dévisser, et aussi des fils ou des nappes (juste 2 ou 3) à débrancher, pour les fils/nappes c'est simple il y a toujours des connecteurs, rien à déssouder
 
Vous trouverez ci-dessous des liens avec photos expliquant comment démonter certains modèles.
 
Une fois démontée il faut emmener toute la partie basse (le fond de l'imprimante qui contient les feutres) dans une baignoire ou un évier, ces feutres sont gorgés d'encre, et ça tache !!!
 
Extraire les feutres en repérant bien leur ordre, il y a en 2 ou 3 ou 4 selon les modèles, chacun de forme différente, mettre le fond de l'imprimante à l'abri, hors de la baignoire ou évier.
 
On arrive au sérieux, on prend les feutres un par un, puis on les presse afin d'en faire sortir l'encre, ne pas presser trop fort tout de même, passer un coup de douchette à l'eau chaude, puis re-presser, puis re-douchette, re-presser etc ....... jusqu'à ce que le liquide sortant du feutre soit clair.
 
On laisse sècher les feutres (en été les miens ont séché en 24h) sur un séchoir.
On peut accélérer le séchage en les passant au sèche cheveux au début.
 
Une fois qu'ils sont bien secs il faut les secouer, les tapoter, pour leur redonner du volume.
 
Il ne vous reste plus qu'à les replacer dans le socle de l'imprimante et à tout remonter.
 
 
4 - DES LIENS INTERESSANTS 
LE site d'où j'ai tiré le principal des procédureshttp://www.printersiam.com/data/Ca [...] edures.htm
Topic en français sur les BJC
http://www.commentcamarche.net/for [...] ote-orange
 
Forum sur les jet d'encre (en anglais)
http://www.fixyourownprinter.com/forums/inkjet
Section du même forum sur le réservoir d'encre usagé plein (en anglais)
http://www.fixyourownprinter.com/f [...] t/15284#65
 
Un forum sur les jet d'encre (en anglais)
http://www.nifty-stuff.com/forum/viewforum.php?id=2
 
Forum d'un site commercial (en français)
http://sosimprimante.com/index.php?act=idx
 
Page perso où il est expliqué comment démonter une BJC3000 (en anglais)
http://mysite.wanadoo-members.co.u [...] onBJC.html
 
Page perso où il est expliqué comment démonter une BJC6500 (en anglais mais beaucoup de photos)
http://www.sitemaster-internet.co.uk/bjc6500/index.htm

 

 

 EPSON




Remise du compteur d'encre imprimante Epson à zéro

Ces sous menus sont prévus pour remettre à zéro le compteur spécial utilisé dans des imprimantes jet d'encre Epson.
Le compteur de protection est le compteur pour l'encre utilisée, il indique à l'imprimante combien d'espace il a dans le plateau spécial où toute l'encre utilisée va pendant les procédures de nettoyage. Avec du temps il sera devenu plein (l'imprimante n'imprimera plus dans ce cas) et l'absorbeur d'encre doit être remplacé. Après remplacement et le remplissage tu dois remettre le compteur à zéro afin de continuer une impression normale. Les articles par type d'imprimante peuvent t'aider à la recharger en ancre.
Montrer la valeur courante du compteur – montre la valeur du compteur de protection. Tu peux l'employer pour voir le résultat de remise à zéro après la procédure.

Remise à zéro du compteur - te permet de remettre à zéro la protection.

Annulation du compteur de dépassement - te permet de remettre à zéro la protection à zéro. Travailler seulement avec le service maintenance d'erreur.

Sur de vieux modèles d'imprimante et que tout fonctionne il peut avoir comme conséquence un message d'erreur si le compteur de protection est déjà au maximum. Employer dans ce cas-ci les instructions de remise manuelle fournies ci-dessous.

Ne pas remettre à zéro le compteur de protection si tu pas remplacé la garniture de rebut d'encre ! Ceci peut endommager la tête par une fuite d'encre, et comme résultat, tête endommagée!

Au-dessous tu trouveras des instructions manuelles de remise à zéro sur des modèles plus anciens d'imprimante (25 modèles d'imprimeur).
1) arrêter l'imprimante.
2) remplacer la garniture de rebut d'encre.
3) effectuer les instructions de remise à zéro pour votre modèle d'imprimante comme ci-dessous.
4) arrêter l'imprimante.
*******************************************************************************
EPSON 7600/9600                                                            
Presser le bouton Power en maintenant " (PAPER SOURCE,PAPER FEED,CUT/EJECT) ".
Lâcher tous les boutons. " Manu " devrait apparaître. Appuyer " DOWN ", " CLEAR COUNTER " devrait apparaître.
Presser " RIGHT " puis " UP " - tu dois voir " MAIN TANK ".
Presser " RIGHT " puis " ENTER " (CUT/EJECT).
Option nettoyage à la mise en route. Séquence d'opérations sur le panneau de contrôle.
(Ready. Selectype. Printer Setup. Scrool down to Maintenance. Selectype. Power Cleaning,. Selectype. Exec. Press Eject).
********************************************************************************
EPSON R300                                                                    
Allumer l'imprimante
Presser " (STOP, MANITENANCE et POWER) " et allumer l'imprimante.
*******************************************************************************
                                                                                                           Photo 950,960
Mettre l'imprimante en marche avec le commutateur de roulement papier et le commutateur de papier pressé. Les indicateurs de papier et d'encre clignoteront toute les 3 secondes. Pendant ce temps, libérer momentanément le commutateur de roulement papier, et puis appuyer sur et tenir le commutateur encore pendant 10 secondes. Quand les contrôles d'imprimante sont terminés, les LED avant s'allumeront 2 secondes, et l'imprimante se mettra alors dans le mode " Standby ". Arrêter l'imprimante.
*******************************************************************************
EPSON RX500
Appuyer sur tous les boutons suivants : " (Power, Load/Eject, Stop, B&W, Color) ", après que l'imprimante soit allumée tu verras " Init eeprom " sur l'écran d'imprimante. Appuyer sur le bouton " Color " pour effacer le compteur de protection.
*******************************************************************************
EPSON RX600
Appuyer sur tous les boutons suivants : " (Power, B&W, Color) ", puis à la demande (tu verras le message sur l'écran de l'imprimante), arrêter l'imprimante.
*******************************************************************************
EPSON C80
Maintenir les deux boutons de papier et d'encre tandis que tu rétablis le courant. Quand la LED " Paper out " clignote relâcher les deux boutons et presser le bouton " Ink-cleaning " pendant au moins 10 secondes. L'imprimante fera un cycle de contrôle et fonctionnera normalement après environ 3 minutes.
********************************************************************************
EPSON 2100
Tourner le bouton " Power " en tenant des boutons un et trois " (ROLL PAPER et SHEET FEEDER) ".
Maintenir alors le bouton un pendant 10 secondes.
*******************************************************************************
EPSON Stylus Color
Presser et maintenir " (ALT+FONT+LOAD+PAUSE) " et maintenant presser le bouton " POWER "
Libérer tous les boutons

*******************************************************************************

EPSON Stylus Color 300
Presser et maintenir les boutons " (LOAD/EJECT " et " CLEANING) ", presser le bouton " POWER " et maintenir jusqu'à ce que tu voies les LED " (INK OUT et PAPER OUT) " clignoter. Relâcher tout les boutons. Dans les 2 ou 3 secondes encore presser " LOAD/EJECT " et puis relâcher
*******************************************************************************

 EPSON Stylus Color 400, 600

Presser et maintenir les boutons " (LOAD/EJECT et " CLEANING " appuyer sur le bouton " POWER "et le maintenir jusqu'à ce que tu voies les LED " (INK OUT " et " PAPER OUT) " clignoter. Relâcher tout les boutons. Dans les 2 ou 3 secondes encore presser " LOAD/EJECT " et puis relâcher
*******************************************************************************
EPSON Stylus Color 440, 640, 740, 460, 660, 670, 760, 860, 880, 1160


Presser et maintenir les boutons LOAD/EJECT et " CLEANING " puis appuyer sur le bouton " POWER "et le maintenir jusqu'à ce que tu voies les LED " (INK OUT " et " PAPER OUT) " clignoter. Relâcher tout les boutons. Dans les 2 ou 3 secondes encore presser " LOAD/EJECT " jusque tout les LED clignotent

*******************************************************************************
EPSON Stylus Color 680

Presser et maintenir les boutons " (LOAD/EJECT et " CLEANING) " puis appuyer sur le bouton " POWER "et le maintenir jusqu'à ce que tu voies les LED " (INK OUT " et " PAPER OUT) " clignoter. Relâcher tout les boutons. Dans les 2 ou 3 secondes encore presser " LOAD/EJECT " jusque tout les LED clignotent
*******************************************************************************

EPSON Stylus Color 800, 850
Presser et maintenir les boutons " (LOAD/EJECT et " CLEANING) " puis appuyer sur le bouton " POWER " et le maintenir jusqu'à ce que tu voies les LED " (INK OUT " et " PAPER OUT) " clignoter. Relâcher tout les boutons. Dans les 2 ou 3 secondes presser et relâcher " CLEANING " tu verra toutes les LED clignoter

******************************************************************************* 

EPSON Stylus Color 900, 980
Presser et maintenir les boutons " (LOAD/EJECT et " CLEANING) ", presser le bouton " POWER " tu verras clignoter la LED " INK OUT "
Relâcher tout les boutons. Dans les 2 ou 3 secondes presser et maintenir " CLEANING " pendant 10 à 12 secondes
*******************************************************************************

EPSON Stylus Color 3000
Presser et maintenir les boutons " (PAUSE, LF/FF et DOWN ARROW) " et mettent en marche l'imprimante. Libérer tous les boutons
*******************************************************************************
EPSON Stylus Photo 785, 895
Presser et maintenir les boutons " (Maintenance et Roll Paper) ", presser le bouton " POWER ", tu verras la LED " ERROR " clignoter

Relâcher tous les boutons. Dans les 2 à 3 secondes la LED clignote et alors presser et maintenir le bouton " Roll Paper " 10 à 12 secondes, jusque toutes les LED clignotent

*******************************************************************************
EPSON Stylus Photo 890, 1280, 1290
Presser et maintenir les boutons " (Maintenance et Roll Paper) ", presser le bouton " POWER ", tu verras la LED " Power led " clignoter
Relâcher tous les boutons. Dans les 2 à 3 secondes la LED clignote et alors presser et maintenir le bouton " Roll Paper " 10 à 12 secondes, jusque toutes les LED clignotent
*******************************************************************************
EPSON Stylus 1520
Mettre en marche l'imprimante en pressant les boutons suivants : " (Alt, LF/FF, Load/Eject, Micro Adjust) " 
*****************************************************************************
                       EPSON Styls Color II, IIS, 400, 600, 640
Mettre en marche et arrêter l'imprimante 5 fois à l'aide du bouton " POWER "

*******************************************************************************

en fin j'éspere que j'ai la solution pour plusieur quandidas

à bien tôt

khalilo6 

 

 remise à zero le compteur d'imprimante CANON+EPSON
ط¨ط¯ط§ظٹط©
ط§ظ„طµظپط­ط©